DM32 Info

DM32 v2.11: 2025-12-05

Fixes

  Fixed: crash after using equation solver with Flag-11 (forum)
  Font design: visually improved a selection of glyphs in the SwissKeys font (the "bold" font).

DM32 v2.10: 2024-08-17

Fixes

  Fixed: Difference in error messages (STAT ERROR and INVALID y^x)
  Fixed: SOLVE (i) asks for solve variable

DM32 v2.09: 2024-05-06

Enhancements

  Added RANDSEED to statefile
  Statefile parsing enhancements
  Stack Right-align option (see in doc)

DM32 v2.08: 2024-03-18

Enhancements

  Added CPU frequency switching when powered from USB
  Added remote calls from CALC mode
  Added Extended GTO functionality (see in doc)
  Added support for automatic load of dependent states (see in doc)

Fixes

  Fixed: The '0' style doesn't match register font in SHOW box
  Fixed: F3 (SST) should act only if no other key processing is pending
  Fixed: F3 (SST) long press to NULL behavior
  Fixed: Remote XEQ calls to current context
  Fixed: First remote XEQ call should clear remote call stack
  Fixed: Current state filename should be pre-selected in "Save" dialog

DM32 v2.07: 2023-12-08

Enhancements

  Added remote XEQ functionality (see in manual)
  Added SHOW view of EQN message
  SHOW extended to all program lines in program mode

Fixes

  F2 key (i.e. debug view toggle) deactivated for non-CALC modes and during number entry
  Fixed USB disk id to 0483:5720 so it corresponds to USB MSC by STM
  Fixed: Program SOLVE ending in "NO ROOT FOUND" prevents subsequently keyed XEQ from running (until pressing [R/S])
  Fixed: Number entered as '1E-' ([E][+/-]) should be interpreted as '1'
  Fixed: Message triangle cut-off after File->Load Clean State
  Fixed: Left/right scrolling of long EQN message (i.e. EQN in PRGM mode with flag10 set) doesn't work

DM32 v2.06: 2023-11-01

  Added "Debug View" (see in manual)
  Added Step-out and Step-over (see in manual)
  SHOW box style changed to better match overall look
  Fixed: Sometimes SHOW displays "SHOW" instead of expected text on long key press
  Fixed: Wrong CLEAR menu in PRGM and EQN mode after elaborated key combinations
  SHOW hold isn't killed by shift presses (simplifies screenshot invocation)
  SHOW hold isn't canceled by screenshot
  Fixed: Integration ends on overflow when Flag5=0 (should give an integration result) .. this also fixed a problem with restarting integration after an overflow
  Fixed: Memory corruption in EQN list (reported by Raul). Exhibit itself during EQN edit by displaying "NO EQN" on other lines and all those equations are lost.

Dear valued customer,

We appreciate your decision to purchase the DM32 calculator. 
As one of our early adopters, your support means a lot to us.

 

In our initial firmware versions, we restricted the CPU speed 
to 48MHz due to power limitations from the CR2032 battery. 
However, in upcoming firmware updates, we're introducing the ability 
to switch to 160MHz when powered by USB. It's crucial to note that 
upon unplugging the USB, the CPU speed must swiftly revert to 48MHz 
to prevent battery voltage drop and subsequent CPU resets.

Regrettably, we've identified an issue affecting units purchased 
before December 2023. In specific scenarios, the CPU speed doesn't 
transition quickly enough, potentially leading to calculator resets.

This may happen upon USB disconnection if the device is engaged in 
processing tasks rather than merely awaiting user input or being powered down.

All units ordered post-November 2023 have been enhanced to ensure consistent 
performance. This modification entails replacing R4 with a 22k resistor 
instead of the previous 100k one.

To address this issue, we offer several solutions:
 

    If you're comfortable soldering, replacing R4 is a straightforward fix. We're happy to dispatch a replacement 
    resistor to you in an envelope, see  https://www.swissmicros.com/product/r4-22k-resistor
    
    Alternatively, you can send your DM32 to us, and we'll replace the resistor and return it to you promptly, 
    see https://www.swissmicros.com/product/rma
    
    We anticipate a new batch of PCBs to be available in approximately three months. Once ready, we can send you 
    a replacement PCB. We kindly request that you return the replaced PCB to us. 
    
    https://www.swissmicros.com/product/dm32-replacement-pcb

 

We sincerely apologize for any inconvenience caused and appreciate your 
understanding and cooperation in resolving this matter.
 
Thank you for your continued support and patience.

 

Best regards

Michael Steinmann

SwissMicros