VHF / HF X-Gate Project - John's Vademecum

Try to learn something about everything, and everything about somethingThomas Huxley “Darwin's bulldog” (1824-1895)

Trace: • Fldigi Parrot • DMR HotSpots • Svx Mobile • MB7AZE SvxLink • YaDDNet Data Backup • CRT SS9900 • Casio Marlin • HF APRS Base Station • DMR and DV Modes • DM16L Progs

You are here: Home » Public Area » Miscellany » Radio » Older Topics » VHF / HF X-Gate Project

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

<-[[.:]]

====== VHF / HF X-Gate Project ======

  * my interpretation of the [[https://www.barrettcommunications.com.au/2062-crossgate/|Barrett Radio 2062 Crossgate]]
  * HF port has syllabic squelch for better detection of SSB speech signals
  * VHF port has DTMF decoder for control commands      
  * Raspberry Pi running a Python application handles control of HF radio via NMEA and of talkthrough functions etc. via GPIO
  * DTMF commands for control of Icom IC-M710 : Frequency, Mode (USB/LSB/AM), Power (20W/50W/100W), ATU Tune cycle 
  * DTMF control of **talk-through** (//HF transceive//) or  **monitor** (//HF Receive//) functions
  * Morse Code (CW) revertives over VHF port to read back parameters such as HF radio //frequency, mode, power// etc.
  * Built in Webserver for status display [[http://gm4slv.plus.com:42109/]]
  * Python code is <del> [[https://github.com/gm4slv/PythonProjects/tree/master/xgate_m710|here on GitHub]]</del>
  * X-Gate will run in //dumb talkthrough// mode if Raspberry Pi controller is removed
  * Operation of uplink port in full duplex on  VHF and UHF is possible, to enable access regardless of state of talkthrough.

===== DTMF Commands =====

^Function^Command^Comment^
|Log on | 0# |  | 
|Log off | *99*# |  | 
|Set Frequency | *1fffff# | ffff.f kHz |
|Set Channel | *1xxxx# | mem chan xxxx |
|Set Mode USB | *21# |  |
|Set Mode LSB | *22# |  |
|Set Mode AM  | *23# |  |
|Set TX Power Low | *41# | 15W |
|Set TX Power Medium | *42# | 50W |
|Set TX Power High | *43# | 100W |
|QSY Down 0.5kHz | *5# |  |
|QSY Up 0.5kHz | *6# |  |
|Monitor HF | *7# | 5 seconds |
|Monitor HF | *7xx# | xx seconds |
|Monitor HF | *7*1# |(Duplex Mode) Continuous Monitor ON |
|Monitor HF | *7*0# |(Duplex Mode) Continuous Monitor OFF |
|ATU Tune | *8# |  |
|Status | *9# |  |
|S-Meter | *91# |  |
|Full Status | *93# |  |
|Talkthrough ON | *01# |  |
|Talkthrough OFF | *00# |  |


===== Further Information =====

| Barrett 2062 Brochure | {{ :public:radio:dormant:2062_cross_gate_brochure_english.pdf |}} |
| Barrett 2062 Manual  | {{ :public:radio:dormant:barrett-2062-hf-vhf-uhf-crossgate-operation-manual-12.pdf |}} |


  * new developments.... [[public:musings:radio:2024:hf-vhf_xgate|]]

---- //[[gm4slv@gm4slv.plus.com|John Pumford-Green]] Wed May  4 17:22:37 2022//

Page Updated : ~~LASTMOD~~

{{tag>radio hf vhf python pi xgate}}

Navigation

Search

Toolbox