Try to learn something about everything, and everything about somethingThomas Huxley “Darwin's bulldog” (1824-1895)

Trace: • Soldersmoke • QMX Two Way QSO • 60m Transceiver • QRSS MEPT • Radio Clubs • blog_history

You are here: Make It Tea » Public Area » Radio » Radio Topics » Arduino Projects » QRSS MEPT

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
public:radio:topics:arduino:qrss_tx [12/07/26 08:04 BST] – [Step one] johnpublic:radio:topics:arduino:qrss_tx [12/07/26 16:39 BST] (current) – [Test Amp] john
Line 2: Line 2:
  
  
-====== QRSS TX ======+====== QRSS MEPT ======
  
-I started work on my small QRSS TX idea with a simple Arduino / SI5351 / 16x2 LCD arrangement.+I started work on my small QRSS MEPT idea with a simple Arduino / SI5351 / 16x2 LCD arrangement. The LCD is only there because I found this breadboard setup already with Seeeduino Nano, SI5351 and LCD in my box of "Arduino Project bits" - from a previous experiment - and I thought I'd keep it for the time being as a display to help in debugging (?). Once the MEPT is functional and ready for operation I'll remove the LCD (and its code from the sketch)
  
 {{:public:radio:topics:arduino:qrss_1.jpg?direct&600|}} {{:public:radio:topics:arduino:qrss_1.jpg?direct&600|}}
Line 21: Line 21:
 {{:public:radio:topics:arduino:gm4slv_test_tx1.jpg?direct&600|}} {{:public:radio:topics:arduino:gm4slv_test_tx1.jpg?direct&600|}}
  
-The sketch+==== The sketch ==== 
 + 
 +++++ Click to read / hide | 
  
 <code c> <code c>
Line 244: Line 246:
 </code> </code>
  
 +++++
  
 ===== Step Two ===== ===== Step Two =====
Line 252: Line 255:
  
  
 +==== Test Amp ====
  
 +I found a 30m PA strip from a previous project that produces about 6W from < 10mV drive, with 3 class-A bipolar driver stages feeding an IRF510 MOSFET - originally intended as a linear amplifier.
 +
 +I've played with the supply volts and the MOSFET bias and can comfortably get up to 3W carrier with 8V supply. It's not terribly efficient but at QRP levels that's hardly relevant.
 +
 +I've got it connected to the Ardiuno/Si5351 and it's on the air running 1W. 
 +
 +{{:public:radio:topics:arduino:mept_1.jpg?direct&600|}}
 +
 +{{:public:radio:topics:arduino:mept_2.jpg?direct&600|}}
 +
 +{{:public:radio:topics:arduino:mept_3.jpg?direct&600|}}
 +
 +I'll use this amp as a blueprint for a new PA for the MEPT, perhaps with fewer stages as I don't need so much gain or linearity.
 +
 +I've seen it on grabbers around Europe 
 +
 +=== Grabber results at 1W ===
 +
 +
 +{{:public:radio:topics:arduino:m0mqw.jpg?direct&600| M0MQW}}
 +
 +{{:public:radio:topics:arduino:sa6bss.jpg?direct&600|SA6BSS}}
 +
 +{{:public:radio:topics:arduino:so5cw.png?direct&600|SO5CW}}
 +
 +At 1533z I reduced power to around 200mW 
 +
 +=== Grabber Results at 200mW ===
 +
 +FIXME
 +
 +
 +===== Stretch Goals =====
 +
 +  * Add a function to generate "Slow FSK Hell" to make waterfall-readable text - see the image of **GM4GHK** below
 +  * Add DFCW
 +  * Add a "normal-speed CW ident" for cases where it might make sense (?)
 +
 +{{:public:radio:topics:arduino:gm4gkh_hell.jpg?direct&600|}}
 ===== Further Information ===== ===== Further Information =====
  
Line 260: Line 303:
 Page updated : ~~LASTMOD~~ Page updated : ~~LASTMOD~~
  
-{{tag>}} +{{tag>radio qrss arduino mept}}
  
 +~~DISCUSSION~~